Online CCNA Lab

By arfs -
The Cisco CCNA network associate certification validates the ability to install, configure, operate, and troubleshoot medium-size routed and switched networks, including implementation and verification of connections to remote sites in a WAN. This new curriculum includes basic mitigation of security threats, introduction to wireless networking concepts and terminology, and performance-based skills. This new curriculum also includes (but is not limited to) the use of these protocols: IP, Enhanced Interior Gateway Routing Protocol (EIGRP), Serial Line Interface Protocol Frame Relay, Routing Information Protocol Version 2 (RIPv2),VLANs, Ethernet, access control lists (ACLs).
(Source: http://lab177.vn2k.net)

Popular posts from this blog

Cisco binary image unpacker

By arfs -
Image
Cisco binary image unpacker is a software that allows you to unpack the IOS and ASA images. Follow this steps to use this software for GNS3. With this way the Router loading process can be faster. This is useful for those of you that do start and stop Router frequently. Donwload Cisco image unpacker 0.1  for Windows. Extract thi zip file to your specific folder.. Copy the IOS file to this folder, for example "c3640-jk9s-mz.124-16a.bin". On windows command prompt, type the following command: "unpack c3640-jk9s-mz.124-16a.bin" (without ""). The output file stored in temporary folder, in my case "C:\Documents and Settings\dion\Local Settings\Temp". Open the folder and you will find the unpacked file "C3640-JK.bin", file size is about twofold. Copy "C3640-JK.bin" to your IOS folder. Your can also rename the file to "c3640-jk9s-mz.124-16a(unpacked).bin" Open GNS3, On the Edit menu, choose IOS image and hyper...
Read more

Connecting to Cisco Router console port using Linux

By arfs -
Image
I tried to connect my Ubuntu laptop to Cisco Router console port. I did successfully. What you will need: A roll-over cable (Cisco Console Cable). These are usually RJ-45 on the router side and serial on the PC side. If your laptop doesn’t have a serial port (like mine) you can get a 9-pin D-sub serial to USB cable. I got the BAFO USB Serial to DB9. I bought it in Ambassador Mall Kuningan Jakarta last night. Get Connected: Connect all the cables: USB -> Serial -> Crossover –> Console Port Download and Install Putty . root@dion-laptop:~# apt-get install putty Make sure that the USB to serial cable is recognized. root@dion-laptop:~# dmesg | grep tty [ 0.004000] console [tty0] enabled [ 1.923508] tty ptyx4: hash matches [ 131.637904] usb 3-2: pl2303 converter now attached to ttyUSB0 [ 173.768300] type=1503 audit(1243914954.561:5): operation="inode_permission" requested_mask="w::" denied_mask="w::" fsuid=0 name="/dev/ttyUSB0" pid=...
Read more

Using DHCP and IP Helper Addresses

By arfs -
Image
Routers Used: 3640 w/ NM-4T and NM-1FE-TX modules IOS: c3640-jk9s-mz.124-16a Objective In this lab, configure a Cisco router to act as a DHCP server for clients on two separate subnets. The IP helper address feature will also be used to forward DHCP requests from a remote subnet. Scenario Clients on the 192.168.3.0/24 network and the 10.0.0.0/8 network require the services of DHCP for automatic IP configuration. Configure Aristo serve both subnets by creating two separate address pools. Finally, configure the FastEthernet interface of the Arief router to forward UDP broadcasts, including DHCP requests, to Aris. Step 1 Build and configure the network according to the diagram. Connect HostA and HostB as shown, but configure these clients to obtain their IP addresses automatically. Because these hosts rely on DHCP, they cannot be tested using ping until Step 5. Configure RIP v2 on Aris and Arief. Be sure to enable updates on all active interfaces with the network command: Aris(config)#...
Read more